|
|
 |
| |
» Specifications
» Motor Performance
» Dimensions
» QuickStart Kit
» Part Numbering and Connectivity
» Options
» Encoders
» Literature
» Software
» Additional Resources
» Contact IMS
|
|
The MDrive17Plus Speed Control is a NEMA 17 size high torque stepping motor integrated with an advanced, high resolution microstepping driver developed for intelligent velocity control from an array of possible input sources. Features include:
- 10-bit analog input which can operate in three different input modes: voltage, current and PWM.
- 20 microstep resolutions from full step to 51,200 steps per revolution.
- Programmable Run and Hold Current
- All parameters are software configuarable (setup utility included) - no external switches or resistors required.
|
|
MDrive17Plus
Base Version |
|
|
Specifications
Open Print View
|
 |
- General
- Motion
- Communications
- Setup Parameters
- Motor
| Input Voltage |
Range (includes back-EMF) |
+12 to +48 VDC |
| Power Supply Current Requirement |
Max per MDrivePlus (Depends on voltage and load) |
2.0 A |
| Speed Control Input |
Input Modes |
Voltage |
0 to +5 VDC, 0 to +10 VDC
|
| Current |
4 to 20 mA, 0 to 20 mA |
| PWM |
15 to 25 kHz PWM |
| Resolution |
10-bit |
| Logic Inputs (Stop/Start, Direction) |
Low Level |
0 to 0.8 VDC |
| High Level |
+2.0 to +5.0 |
| Internal Pull-up Resistance (to 3.3 VDC) |
20kΩ |
| Operating Temperature |
Measured at Heat Sink (non-condensing humidity) |
85°C |
| Measured at Motor (non-condensing humidity |
100°C |
| Oscillator Frequency |
|
5 MHz (Max) |
| Microstep Resolution |
Number of Settings |
20 |
| Steps per Revolution |
200, 400, 800, 1000, 1600, 2000, 3200, 5000, 6400, 10000, 12800, 20000, 25000, 25600,
40000, 50000, 51200, 36000 (0.01 deg/μstep),
21600 (1 arc minute/μstep), 25400 (0.001mm/μstep) |
| Protocol |
SPI (Serial Peripheral Interface) |
| Isolation |
Galvanic |
| |
Function |
Range |
Units |
Default |
| A1 |
Analog Input Mode |
0 to +5 VDC, 0 to +10 VDC, 4 to 20 mA, 0 to 20 mA, 15 to 25 kHz PWM |
— |
0 to +5 VDC |
| ACCL |
Acceleration |
91 to 1.5 X 109 |
steps/second2 |
1,000,000 |
| C |
Joystick Center |
1 to 1022 |
counts |
0 |
| DB |
Analog Deadband |
0 to 255 |
counts |
1 |
| DECL |
Deceleration |
91 to 1.5 X 109 |
steps/second2 |
|
| DIR |
Motor Direction Override |
CW/CCW |
— |
CW |
| FAULT |
Fault/Checksum Error |
Error Code |
— |
none |
| FS |
Analog Full Scale |
1 to 1023 |
counts |
1023 |
| HCDT |
Hold Current Delay Time |
0 or 2 to 65535 |
msec |
500 |
| IF |
Analog Input Filter |
1 to 1000 |
counts |
1 |
| MHC |
Motor Hold Current |
0 to 100 |
Percent (%) |
5 |
| MRC |
Motor Run Current |
1 to 100 |
Percent (%) |
25 |
| MSDT |
Motor Settling Delay Time |
MSDT+HCDT <= 65535 |
msec |
0 |
| MSEL |
Microstep Resolution |
See Spec Motion Settings Tab |
µsteps/step |
256 |
| SSD |
Stop/Start Switch Debounce |
0 to 255 |
counts |
0 |
| VI |
Initial Velocity |
0 to <VM |
steps/second |
1000 |
| VM |
Maximum Velocity |
VI to 5,000,000 |
steps/second |
768,000 |
| USER ID |
User ID |
1 to 3 characters |
Viewable ASCII |
IMS |
| |
Single Length |
Double Length |
Triple Length |
| Holding Torque oz-in (N-cm) |
32 (22.6) |
60 (42.4) |
74.9 (52.9) |
| Detent Torque oz-in (N-cm) |
1.66 (1.17) |
2.08 (1.47) |
3.47 (2.45) |
Rotor Inertia
oz-in-sec2 (kg-cm2) |
0.00053 (0.038) |
0.00080 (0.057) |
0.00116 (0.082) |
| Weight Motor+Driver lb (gm) |
10.4 (294.8) |
12.0 (340.2) |
15.2 (430.9) |
|
 |
Motor Performance Curves
Open Print View |
|
|
|
Dimensions
Open Print View
|
|
|
|
| QuickStart Kit |
 |
All-inclusive QuickStart Kits facilitate rapid design verification by bundling any one of over 156,000 MDrivePlus products -- built to your specifications -- with everything needed to connect quickly and conveniently, enabling engineers to confirm with confidence that their application’s design goals are met. QuickStart Kits include: a single sheet instruction guide, software/manuals CD, and connecting cabling including Communications Converter and Prototype Development Cable(s).
Order QuickStart Kits simply by placing a “K-” at the beginning of an MDrivePlus part number |
| CONNECTIVITY NOTE: Communications Converters and Prototype Development Cables, in addition to Mating Connector Kits for use in building your own cables, are available separately. Refer to the following section for more complete details. |
|
|
Part Numbering and Connectivity
Open Print View |
|
|
|
 Use the drop-down menu above to view mating connector
interface options by MDrivePlus part number (p/n) defined via the preceding order table or
interactive MDrivePlus Part Builder.
Note: asterisks (*) are used with drop-down menus where there is no impact to connector options.
Image left: example of mating connector interface details accessed through pull-down menus above.
|
| |
- Comm Converters
- Prototype Development Cables
- Mating Connector Kits
Electrically Isolated, in-line converters pre-wired with mating connectors to conveniently set parameters and program a single MDrivePlus via a PC USB port.
To view connectivity options for each model MDrive, select from the drop-down listing above.
| Converter Part Number |
Mating Connector Type |
| MD-CC300-001 (USB to SPI) |
10-Pin IDC |
| MD-CC302-001 (USB to SPI) |
10-Pin Friction Lock Wire Crimp |
If building your own cabling, you will need:
- SPI inline converter or PC parallel port
- Appropriate Mating Connectors
- Cabling with appropriate mating connectors for the MDrive model selected
No Prototype Devlopment Cables applicable to this product.
Used to build your own cables. Kits contain 5 mating connector shells with pins. Cable not supplied. Manufacturer crimp tooling recommended.
To view connectivity options for each model MDrive, select from the drop-down listing above.
|
|
Options |
|
|
|
Encoders |
|
External single-end and differential optical encoders are
offered factory-mounted with the MDrive23Plus. Available with the following line counts: 100, 200, 250, 256, 400, 500, 512, 1000, 1024. All encoders come with an index mark.
Optional encoder cables are available. Order separately.
Optional encoder cables are available. Order separately.
Single-end Cable (12.0"/30.5cm) ...................ES-CABLE-2 [wire colors]
Differential Locking Cable (6.0'/1.8m) .........ED-CABLE-6 [wire colors]
|
|
Literature [Acrobat PDF] |
|
|
|
Software |
|
|
|
| Additional Resources |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
